Drilling Equipment Sales, Inc., Your Home for Drill Rigs, Drilling Equipment, Water Trucks, Pump Hoists, Grouters, and parts and accessories for the drilling industry.
Drilling Equipment Sales      2515 HWY 70 SW Hickory, NC 28602 • Tel: 828/322-3056 • Fax: 828/322-4042

Used Equipment Available At DES:

BUCYRUS ERIE CANTERRA CHALLENGER CHICAGO PNEUMATIC CME
COOPER DIEDRICH DRILMASTER DRILTECH DSI
FAILING FRANKS GARDNER DENVER GP IDECO
INGERSOLL-RAND JOY SULLIVAN MAYHEW MIDWAY MISCELLANEOUS
MOBILE PORTADRILL PUMP HOIST REICHDRILL SANDERSON CYCLONE
SARGENT SCHRAMM SHOPBUILT SIMCO SKYTOP BREWSTER
SPEEDSTAR VERSADRILL WALKER NEER WATER TRUCKS WILSON


BUCYRUS ERIE

1963 Bucyrus Erie 10R Status: In Stock VIN#: 1

Rig Options
  • Manual Clutches on the Drawworks
  • P/B Gasoline Engine (operates the drawworks and rotary table)
  • Detroit 671 Deck Engine  (operates the compressor only)
  • Leroi 256 Reciprocating Air Compressor
  • 8-1/2" Retractable Rotary Table
  • Three Hydraulic Leveling Jacks
  • 35' Square Tubing Derrick
  • Bailing Drum
  • No Drill Pipe Rack
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1963 Ford Chassis
Get a Quote for this Vehicle
No Picture Available

Back to Top
CANTERRA

CT311M-5 Mud Rotary Drill Status: In Stock VIN#: 0

Rig Options
  • Weight: Typically less than 20,000 lbs with pipe, tools and accessories
  • Height: 11 feet (mast down)
  • Power takeoff: Hydraulic pumps driven off transfer case
  • Rotary:
    • Standard 36,000 in-lb (3,000 ft/lb), 0-150 rpm infinitely variable top drive
    • Hydraulic rotary top drive
  • Pullup: 20,000 lb Pulldown: Capable of 20,000 lb but limited by drill weight to approximately 13,000 lb
  • Mast: Rated at 36,000 lb pullback system, plus double line on drawworks winch, stroke 23 ½'
  • Operator's console: Complete with all necessary controls, gauges, etc.
  • Drawworks Winch:
    • Pulls directly over hole with tophead swung out
    • Equipped with 80 feet 9/16" wire rope
    • Hhydraulic failsafe brake
    • 8,000 lb pull @ 240 fpm - single line
    • 16,000 lb pull @ 120 fpm - double line
  • Casing Handling:
    • Tophead swings aside to use drawworks
    • Handles up to 24 foot lengths of 10 3/4" outside diameter casing
  • Pipe rack: 24 lengths of 20 feet x 4" diameter, pipe slide built in
  • Accessories Cabinet: Locking storage for tools and accessories
  • Jacks: Four 36" stroke hydraulic jacks with load checks mounted on drill frame
  • Piston mud pump: 5x6 Gardner Denver mud pump, hydraulically driven, 150 US gpm @310 psi
  • Powered swing out: Top drive unlatches and swings open hydraulically
  • Development Air: 135 cfm x 125 psi hydraulically driven screw compressor
  • Desander: Complete with stand and all plumbing
  • Mud pit: Folds up behind drill for transport. Includes: tee at hole and trough to pan. Cuttings collect in basket which dumps using winch. Complete with jet mixer, manifold to hook up water truck and all hoses
  • Approx. 400' of 2 7/8 OD drill rod (15' length)
  • Misc. subs and bits
  • Rotary air compressor
  • Transfer case replaced before last well was drilled
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Ford F700
  • 4x4
  • 390 CID Detroit Diesel Powered Engine
  • 5 Speed
  • Manual Transmission
Get a Quote for this Vehicle

Click Here for a Larger Picture
Click Here for a Larger Picture
Click Here for a Larger Picture
Click Here for a Larger Picture

Back to Top

1989 Canterra 150 Status: In Stock VIN#: 2

Rig Options
  • 896 Hours Since New
  • No Air Compressor or Mud Pump
  • Space Available on Trailer to Mount a Self-Contained Centrifugal Mud Pump
  • Hydraulic Break-Out Wrench
  • Cat Head
  • Auger Rotary Head Option with 6,000 Ft.-Lbs. Torque @ 0 – 60 RPM
  • Mast with 12’ Stroke for Handling 10’ Drill Pipe
  • 12,000 Lbs. Pullback Force @ 0 – 125 FPM
  • 14,500 Lbs. Pulldown @ 0 – 95 FPM
  • 3,000 Lb. Capacity Planetary Hydraulic Winch
  • Split Spoon Driver Winch with Free Fall
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Tandem Axle Bumper Pull Trailer
  • Powered by a Cummins 4B3.9 76 HP Diesel Engine
Get a Quote for this Vehicle

Back to Top
CHALLENGER

1980 Challenger 124 Status: In Stock VIN#: 3

Rig Options
  • Gardner Denver 5-1/2" X 8" Mud Pump
  • Space and Drive to Mount an Air Compressor
  • Challenger Double Drum Drawworks with Wichita ATD216 Air Clutches (16,500 lbs. single line pull)
  • Single 6" Wide X 28" O.D. Brakes
  • 60,000 Lbs. Capacity X 45' Long 2-1/2" Square Tubing Derrick
  • Bailing Drum with Single Plate 18" Air Clutch and Single 6" Wide X 28" O.D. Brake
  • Retractable Howard Turner 9" Rotary Table
  • 15,000 Lb. Hydraulic Chain Feed Pulldown with 1-3/4" Pitch Chain
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1980 Paystar 5000 Chassis
  • P/B Cummins 350 HP Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Challenger M-320 Status: In Stock VIN#: 4

Rig Options
  • P/B Dertroit 12V71 Engine
  • High Back Table
  • 18" Howard Turner
  • 64' Derrick Rated to 150,000 Lbs
  • Allison Transmission
  • Racking Board
  • Block & Hook
  • 3-1/2" ID Water Course Swivel
  • PARMAC Hydromatic Brake
  • Catheads
  • Located in Europe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Three Axle Trailer
Get a Quote for this Vehicle
No Picture Available

Back to Top
CHICAGO PNEUMATIC

1980 Chicago Pneumatic RT1800 Status: In Stock VIN#: 6

Rig Options
  • No Air Compressor or Mud Pump On-Board (drives available for both)
  • 50' Derrick for Handling Range III Casing
  • No Drill Pipe Rack
  • Bailing Drum
  • Air Clutches on the Drawworks
  • Hydrostatically Powered 10-1/4" Retractable Rotary Table
  • Three Hydraulic Leveling Jacks
  • Double Brake Bands on Kelly and Hoist Drums
  • Rated 60,000 Lbs. Capacity
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 6X4 Crane Carrier
  • P/B Cummins NTA400 HP Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Chicago Pneumatic T650SS Status: In Stock VIN#: 7

Rig Options
  • CAT 3406 425 HP Deck Engine (rebuilt 2003)
  • 50,000 Lb. Pulback
  • CAT 3406 Deck Engine
  • GHH 825 cfm / 300 psi
  • No Drill Pipe Rack
  • No Carousel
  • 1,800' of 4-1/2" X 25' Drill Pipe Available
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a CCC
  • P/B CAT 3208 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Chicago Pneumatic T650WS Status: In Stock VIN#: 8

Rig Options
  • CAT 3406 425 HP Deck Engine (rebuilt 2003)
  • GHH 825 cfm / 300 psi Compressor (rebuilt in 2000)
  • Drill Pipe Handling Tools
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Ford 8000 Chassis
  • P/B CAT 3208 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1968 Chicago Pneumatic T650W Status: In Stock VIN#: 9

Rig Options
  • Deck Engine
  • 450 cfm / 250 psi Reciprocating Compressor
  • Centrifugal Mission 3"X4" Mud Pump
  • Set-Up to Handle 4-1/2" O.D. X 20' Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 6X4 Chassis
Get a Quote for this Vehicle
No Picture Available

Back to Top

1976 Chicago Pneumatic T672W Status: In Stock VIN#: 10

Rig Options
  • Rebuilt Sullair 750/350 Compressor
  • 50,000 Lb. Pullback
  • 1,000' of 4-1/2" Drill Pipe
  • Water Injection Pump
  • DHD Lubricator
  • 1,000' of 4-1/2" Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1987 Mack Chassis
  • P/B CAT 343 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top
CME

CME Auger Rig - 55 Status: In Stock VIN#: 0

Rig Options
  • 6 Cylinder 300ci Ford Gas Engine date 11-2-77
  • Runs Perfect and is Ready to Drill
  • Comes with all Tooling
  • Is in Working Condition.
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Is mounted on 1991 international DT466
  • Allison Auto
  • Truck has 202790 miles
Get a Quote for this Vehicle
   

Back to Top
COOPER

Cooper LTO 350 Status: In Stock VIN#: 5

Rig Options
  • 55' Single Piece Derrick Rated for 150,000 Lbs.
  • Inside Width of Derrick is 62"
  • Double Drum Drawworks with Air Clutches
  • 42" X 10" and 42" X 8" Brakes on Each Drum
  • 1" Diameter Cable
  • Hacker OB-12 Rotary Table
  • BJ Two Sheave Blocks
  • 40' X 4" Square Kelly
  • Oilwell 212P 6" X 12" Duplex Mud Pump Mounted on the Deck
  • Hydraulic Leveling Jacks
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Cooper 8X4 Carrier
  • P/B CAT 3406 Engine
  • Fuller 8 Speed Transmission
Get a Quote for this Vehicle
No Picture Available

Back to Top
DIEDRICH

No Diedrich Listings Available At This Time.

Back to Top
DRILMASTER

1995 Drillmaster 400 Status: In Stock VIN#: 11

Rig Options
  • Gardner Denver 5" X 6" Mud Pump
  • 350 cfm / 150 psi Air Compressor
  • Four 36" Stroke Hydraulic Leveling Jacks
  • 12,000 Lbs. Main Winch
  • Drill Pipe Rack
  • Hydraulic Break-Out Wrench
  • Air Operated Sliding Holding Wrench
  • Jib Boom with Swing and Extend Function
  • Dual Torque Tophead Drive with Off-Hole Slide Feature
  • Tool Box
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on an International 4X4 Chassis
Get a Quote for this Vehicle
No Picture Available

Back to Top
DRILTECH

2007 Driltech D25KW Status: In Stock VIN#: 12

Rig Options
  • 1,300 Total Hours Since New
  • CAT C15 Deck Engine
  • Sullair 1000 cfm / 350 psi Air Compressor
  • DHD Lubricator
  • Water Injection Pump
  • 840' of 4-1/2" O.D. Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top

Three 1994 - 1995 Driltech T40K's Status: In Stock VIN#: 13

Rig Options
  • Three 1994 - 1995 Dritlech T40K's
  • 1050/350's Compressors
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Ford Chassis
Get a Quote for this Vehicle
No Picture Available

Back to Top

1991 Driltech D40K Status: In Stock VIN#: 14

Rig Options
  • 70,000 Lbs. Pullback
  • Cummins KTA19 deck Engine (3,000 hours on rebuild)
  • Sullair 1160 cfm / 350 psi Compressor
  • Set-Up for 20' Drill Pipe
  • Inside and Outside Carousels
  • New Engine Radiator
  • Cooling Fan and Mount
  • Both Feed Cylinders were Resealed Two Years Ago
  • Table has Been Modified to Swing Open and Hydraulically Retract
  • Set-Up with a Casing Hammer Air Latch
  • Other items available at an additional cost
    • Atlas 3000 Casing Hammer
    • Casing Extractor
    • 720' of 4-1/2" O.D. X 20' Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Crane Carrier
  • P/B Cummins L10 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1988 Driltech D25KW Status: In Stock VIN#: 15

Rig Options
  • 840 cfm / 350 psi
  • CAT 3406 Deck Engine
  • Rig was completely rebuilt in 1995
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES
  • 840 cfm / 350 psi
  • CAT 3406 Deck Engine
  • Rig was completely rebuilt in 1995
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Ford 8000 Chassis
Get a Quote for this Vehicle
No Picture Available

Back to Top

1987 Driltech D25KW Status: In Stock VIN#: 16

Rig Options
  • 840 cfm / 350 CompressorC
  • AT 3406 Deck Engine
  • 300' of 4-1/2" O.D. X 20' Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 6X4 Ford Chassis
Get a Quote for this Vehicle
No Picture Available

Back to Top
DSI

1979 DSI "Quick Drill" Status: In Stock VIN#: 17

Rig Options
  • Rig is Powered Off of Chassis PTO
  • Dual Rotation Motors
  • Developmental Joy Rotary Screw Compressor (220 cfm / 120 psi)
  • Gardner Denver 5" X 6" Mud Pump
  • Four Hydraulic Pumps
  • Three Hydraulic Leveling Jacks
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1979 International Chassis
  • P/B CAT 3208 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top
FAILING

Failing CF15 Drilling Rig Status: In Stock VIN#: 0

Rig Options
  • Gardner Denver 5" X 8" Mud Pump
  • 8-1/2" Retractable Rotary Table
  • Air Clutches
  • Drill Pipe Rack
  • Four Hydraulic Leveling Jacks
  • Spicer 784 Transfer Case
  • Little Giant 2" Swivel
  • Boyles Brothers Derrick
  • Basic Tools
  • 700' of 3-1/2" O.D. X 20' X 3-1/2" IF Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 1990 Ford 8000 Chassis
  • P/B Ford 275 HP Engine
Get a Quote for this Vehicle

Click Here for a Larger Picture
Click Here for a Larger PictureClick Here for a Larger PictureClick Here for a Larger Picture

Back to Top


1987 Failing F-10-WT Status: In Stock VIN#: 18

Rig Options
  • Cummins 8.3CT Deck Engine
  • Angle Drilling
  • Wiggle Tail
  • 15,000 Ft.-Lbs. Torque @ 0 - 934 RPM
  • 9-3/4" Spindle Opening
  • 25,000 Lbs. Pulldown and Retract Force
  • 11' Tophead Drive Travel
  • Completely Tooled with New 4-1/4" Augers and Split Spoons
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • International P/B DT466 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing 1250 Status: In Stock VIN#: 19

Rig Options
  • Retractable Failing 5-1/2" Rotary Table
  • Mechanical Clutches on the Drawworks
  • Four Hydraulic Leveling Jacks
  • Drill Pipe Rack
  • 3-1/2" X 24' Fluted Kelly
  • Failing FM45 5X6-1/4" Mud Pump
  • Space for an Air Compressor is Required
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1998 International 4900 Series 6X4 Chassis (260K Miles)
  • P/B DT-466 210 HP Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing CF15 Status: In Stock VIN#: 20

Rig Options
  • Hydraulically Driven Gardner Denver FY-FXX 7-1/2" X 10" Mud Pump
  • 8-1/2" Retractable Rotary Table
  • Air Clutches on the Drawworks
  • Four Hydraulic Leveling Jacks
  • 50' Derrick
  • 24' Long X 4-1/4" Fluted Kelly
  • 3" Swivel & Mud Piping
  • Auxiliary Hydraulic Winch
  • Drill Pipe Rack
  • Drill String Weight Indicator
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 2002 Western Star 8X4 (Twin Steer Front Axle) Chassis
  • P/B CAT C12 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing 1500 Status: In Stock VIN#: 21

Rig Options
  • Gardner Denver 5" X 8" Mud Pump (new bull gear and bearings)
  • Mud Pan
  • 28' Kelly
  • New Chains and Bearing in Break-Out Table
  • New Quill
  • International Propane Deck Engine that Operates Everything Except for the Mud Pump
  • Mud Pump Operates Off of the Truck Engine
  • 780' of 2-3/8" Mayhew Regular X 20' Drill Pipe
  • 1,000 Gallon Poly Water Tank on Trailer
  • Drill Bits
  • Under Reamer
  • Murphy Plug
  • Ingersoll-Rand 100 CFM Screw Portable Air Compressor
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1993 Freightliner FL70 6X4 Chassis
  • P/B Cummins Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1971 Failing CF15 Status: In Stock VIN#: 22

Rig Options
  • No Pipe Rack
  • Air Clutches
  • 8-1/2" Retractable Rotary Table
  • Three Hydraulic Jacks
  • Sandline Drum
  • 4-1/2" Fluted Kelly
  • Failing 5X6-1/4" Pump
  • 3X4 Centrifugal Mud Pump
  • Pulldown is available, but has been removed
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Mack Chassis (rebuilt front end)
  • P/B Mack Diesel Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

1971 Failing CF15 Status: In Stock VIN#: 23

Rig Options
  • LeRoi 100S2 Compressor
  • Failing FM45 5" X 6-1/4" Mud Pump
  • Hydraulic Chain Pulldown
  • Mechanical Friction Clutches on the Drawworks
  • 3-5/8" O.D. Fluted Kelly
  • Retractable Failing 8-1/2" Rotary Table
  • Three Hydraulic Leveling Jacks
  • Martin Decker Drill String Weight Indicator
  • Hydraulic Utility Hoist
  • No Drill Pipe Rack
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1971 International Chassis
  • P/B Detroit 6V92TA 305 HP Engine
  • Fuller 10 Speed Transmission
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing 1250 Status: In Stock VIN#: 24

Rig Options
  • 5-1/2" Retractable Rotary Table
  • Developmental Dresser 990 Reciprocating Air Compressor
  • Gardner Denver 5X6 Mud Pump
  • Four Hydraulic Leveling Jacks
  • Hydraulic Pulldown
  • Bailing Drum
  • Drill Pipe Rack
  • Air Shift Transfer Case
  • 300' of 3-1/2" Drill Pipe (almost new cond.)
  • (1) Drill Collar
  • Little Giant Swivel
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1995 International Single Axle 4900 Series Chassis
  • P/B DT466 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing CF2000 Status: In Stock VIN#: 25

Rig Options
  • 58' Derrick
  • Hydraulic Chain Pulldown
  • Gardner Denver FD-FXX 5-1/2" X 8" Mud Pump
  •     (like new condition, new expendables)
  • 18" Failing Rotary Table
  • Air Clutches
  • Sandline Drum
  • Hydraulic Leveling Jacks
  • Catheads
  • Weight Indicator
  • Twin Detroit 471 Engines
  • This is a very low hour rig.
  • Purchased new by the US Core of Engineers in the early 1970's and stored through 1999 when it was purchased by a driller located in Virginia.
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Tandem Axle Trailer
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing CF2000 Status: In Stock VIN#: 26

Rig Options
  • 48' Derrick Rated for 75,000 lb. Capacity
  • McKissick Three Sheave Blocks
  • Hydraulic Chain Pull down (missing chains)
  • Rebuilt Hydraulic Leveling Jacks
  • Rebuilt Derrick Raising Cylinders
  • 34' X 4-1/2" O.D. Fluted Kelly
  • Rebuilt Brewster 12" Rotary Table (new bearings and seals)
  • Rebuilt Rotary Table Reversing Box
  • Power Take-Off Rebuilt
  • Rebuilt Power Divider
  • Air Clutches on Drawworks
  • Drawworks May Need New Ring Gear and Pinion (one or two teeth believed to be chipped)
  • Catheads
  • Weight Indicator
  • Skid Mounted Oilwell 212P 7-1/4" X 12" Pump P/B Detroit 671 Engine (new engine radiator)
  • 35' Rolling Tailboard Oilfield Trailer
  • Four 5" O.D. Drill Collars
  • +2,000' of 2-7/8" O.D. Drill Pipe (20' & 30' lengths) & 3 or 4 Drill Collars (drill pipe is in poor condition)
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Tandem Axle Mack Chassis (all windows, lights and gauges have been broken)
  • Powered by a Mack Maxidyne 300 HP Diesel Engine (needs an injector replaced, but runs)
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing 1250 Status: In Stock VIN#: 27

Rig Options
  • 5X6 Mud Pump
  • No Air Compressor
  • 8-1/2" Retractable Rotary Table
  • 24' Fluted Kelly
  • 150' of 3-1/2" Flush Joint Drill Pipe
  • Rig has sat idle for a few years
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1959 International 6X4 Chassis
  • P/B Gasoline Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing 1250 Status: In Stock VIN#: 28

Rig Options
  • LeRoi 256 Compresssor
  • Drill Pipe Rack
  • No Mud Pump
  • Retractable 5-1/4" Rotary Table
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1981 Ford L8000
  • P/B Detroit 671 Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top
1980 Failing Jed-A Status: In Stock VIN#: 29

Rig Options
  • Flip Up 18" Rotary Table
  • 49' 6" Mast (can handle double random casing)
  • Stacked Drum Failing Drawworks with PO-216 Air Clutches that Pull 15,000 lbs. on a Single Line
  • Double Brake Bands on Both Kelly and Hoisting Drums
  • Third Drum Sandline Rated at 4,000 lbs. Single Line Pull
  • Four Hydraulic Leveling Jacks
  • McKissick Three Sheave Traveling Block on Kelly Drum
  • Failing Two Sheave Traveling Block on Hoisting Drum
  • Packer Jr. Drill String Weight Indicator
  • King 25XV Swivel
  • Foster Cathead with Spinning Chain
  • Hydraulic Break-Out Cylinder
  • Web Wilson Type "D" Break-Out Tongs
  • Drill Pipe Elevators
  • Complete Set of Bit Crossover Subs
  • Skid Mounted Gardner Denver 7-1/4" X 10" Mud Pump P/B Detroit 671 Engine
  • 1,000' of Drill String (960' drill pipe, 40' drill collar, 26' Kelly)
  • Shop Built Reverse Swivel and Kelly with 230' of 6" X 10' Flanged Drill Pipe
  • 24" Moab Bit
  • Monarch 6" X 6" Self Priming Centrifugal Mud Pump P/B John Deere Diesel Engine
  • Skid Mounted Doghouse 8' X 20' or Option of Small Doghouse Mounted on a Single Axle Trailer with a 2" Ball Hitch
  • 1973 Hobbs 40' Drill Pipe
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a 1980 Ford LT9000 Chassis
  • P/B Cummins 290 HP Engine
Get a Quote for this Vehicle
No Picture Available

Back to Top

Failing 2500 Status: In Stock VIN#: 30

Rig Options
  • 65' X 90,000 lb. SHL Stiff Leg Derrick
  • 290 HP Cummins Diesel Engine w/ Allison 750 Transmission
  • Failing Double Drum Drawworks
  • Failing M-300 Traveling Blocks on 4 Lines
  • 18" Failing Direct Drive Rotary Table
  • Failing Catheads
  • Web Wilson Type B Tongs with assorted Heads
  • Tatco Weight Indicator
  • Manual Leveling Jacks
  • 600 Gallon Fuel Tank
  • Halogen Lights (rig run).
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • Mounted on a Tandem Axle Trailer
Get a Quote for this Vehicle
No Picture Available

Back to Top
FRANKS

Franks Reverse Circulation Rig Status: In Stock VIN#: 31

Rig Options
Powered by Two Ford Six Cylinder Industrial
    Gasoline Power Units
6" Centrifugal Pump On-Board
Retractable Franks 16" Rotary Table
Mechanical Friction Clutches on the Drawworks
Hydraulically Raised Derrick
6" O.D. X 14' Long Kelly
Hydraulic Leveling Jacks on Front
Mechanical Screw Jacks on Rear
200' of 6" X 10' Flanged Drill Pipe
Miscellaneous Assortment of Drill Collars, Bits
    and Handling Tools

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Single Axle Trailer

Get a Quote for this Vehicle
No Picture Available

Back to Top

Franks FJ5 Status: In Stock VIN#: 32

Rig Options
Gardner Denver Air Compressor
3X4 Centrifugal Mud Pump
28' Kelly
300' of 3" O.D. Drill Pipe
5-1/4" Retractable Rotary Table
Ford 300 CID Six Cylinder Gas Deck Engine

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford F600
Powered by a Gasoline Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

Franks 3500 Status: In Stock VIN#: 33

Rig Options
Single Drum Drawworks
P/B Detroit 671 Engine
Hydraulically Raised Single Piece Derrick

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Tandem Axle Trailer

Get a Quote for this Vehicle
No Picture Available

Back to Top
GARDNER DENVER

Gardner Denver 1500 Status: In Stock VIN#: 34

Rig Options
Gardner Denver 7-1/2" Retractable Rotary Table
Gardner Denver 5X8 Mud Pump
Gardner Denver 580 Air Compressor
Manual Clutches on the Drawworks
Four Hydraulic Leveling Jacks
Hydraulic Chain Pulldown

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1997 Ford L9000 Chassis
P/B Cummins N14 350 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1979 Gardner Denver 1500 Status: In Stock VIN#: 35

Rig Options
Gardner Denver 5-1/2" X 8" Mud Pump
10" Retractable Rotary Table
Air Clutches on the Drawworks
Four Hydraulic Leveling Jacks
Hex Kelly
Damaged Chassis Cab and Derrick due to
    Derrick Raising Cylinder Collapse

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1979 Ford 9000 Chassis
P/B CAT 3208 Engine
13 Speed Road Ranger Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Gardner Denver 1500 Status: In Stock VIN#: 36

Rig Options
7-1/2" Retractable Rotary Table
Gardner Denver 5X6 Mud Pump
Gardner Denver ADL Developmental Air Compressor
Four Hydraulic Leveling Jacks
Air Clutches on the Drawworks
4-1/4" X 24' Fluted Kelly
Gardner Denver "Tear Drop" Single Sheave
    Traveling Block
Sandline Drum

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1993 Mack Chassis

Get a Quote for this Vehicle
No Picture Available

Back to Top

Gardner Denver 1500 Status: In Stock VIN#: 37

Rig Options
Gardner Denver 5-1/2" X 8" Pump
Small LeRoi Compressor
Manual Clutches on the Drawworks
Non-Retractable 7-1/2" Rotary Table
1300' of Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1974 Ford 8000
P/B Dertoit Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1976 Gardner Denver 1400 Status: In Stock VIN#: 38

Rig Options
Ingersoll-Rand 750 cfm / 350 psi Screw
    Compressor
Gardner Denver 5" X 6" Mud Pump
Four Hydraulic Leveling Jacks
Drill Pipe Rack
Air Clutches
7-1/2" Retractable Rotary Table

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Freightliner Chassis

Get a Quote for this Vehicle
No Picture Available

Back to Top

1972 Gardner Denver 14W Status: In Stock VIN#: 39

Rig Options
New Heavy Duty 38' Derrick
Gardner Denver WEJ Compressor
Air Clutches on Drawworks
Rebuilt Bailing Drum (March 2007)
New DSM 7-1/2" Rotary Table (March 2006)
Rebuilt Rear Hydraulic Jacks (October 2006)
New Pull down Motor (October 2006)
Rebuilt Transfer Case (March 2007)
980' of 3-1/2" X 20' X 2-3/8" IF Flush Joint Drill
    Pipe (300' new as of March 2006)
24' Gooseneck Trailer
(1) 7-1/2" X 20' Stabilizer
(1) 5-1/2" X 20' Drill Collar
(1) 4-1/2" X 2-3/8" IF Starter Sub

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 6X4 Crane Carrier
P/B Rebuilt Cummins 350 HP Engine
    (October 2006)
Rebuilt 10 Speed Transmission
    (October 2006)

Get a Quote for this Vehicle
No Picture Available

Back to Top

1974 Gardner Denver 14W Status: In Stock VIN#: 40

Rig Options
Air Clutches on the Drawworks
Gardner Denver WEJ Air Compressor
No Mud Pump (clutch intact)
Bean 9 GPM Water Injection Pump
Bailing Drum
7-1/2" Retractable Rotary Table
Hydraulic Chain Pulldown
Three Hydraulic Leveling Jacks

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 6X4 Crane Carrier
Rebuilt Cummins 300 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1984 Gardner Denver Falcon 70 Status: In Stock VIN#: 41

Rig Options
NEW Detroit 12V71TT Deck Engine
1000/350 GHH Compressor
Gardner Denver FD-FXD 5" X 10" Mud Pump
    Mounted Behind the Chassis Cab
FMC Bean 35 GPM Water Injection Pump
70,000 Lb. Pullback Chain Feed System
45' Derrick Handles Range II Casing
Carousel Set-Up to Handle 4-1/2" O.D. X 25'
    Drill Pipe
Five Hydraulic Leveling Jacks

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1984 International
    Paystar 5070 8X4 Chassis
P/B Detroit 6V92TA 300 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Gardner Denver 1000 Status: In Stock VIN#: 42

Rig Options
Air Clutches on the Drawworks
Two Gardner Denver 5" X 6" Mud Pump
    (late style)
3" Plumbing
7-1/2" Retractable Rotary Table
Four Hydraulic Leveling Jacks
Hydraulic Chain Pulldown
No Air Compressor
Drill Pipe Rack
24' Fluted Kelly
Chain Style Break-Out Tong

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1994 Ford 9000 Chassis
P/B Rebuilt CAT 3406 425 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1965 Gardner Denver 2000 Status: In Stock VIN#: 43

Rig Options
Manual Clutches on the Drawworks
10" Retractable Rotary Table
No Pulldown System
CAT 3208 Engine Operates the Mud Pump
Gardner Denver FY-FXX 7-1/2" X 8" Duplex
    Mud Pump
Set-Up on a Six Part Line
Detroit 471 Operates the Drawworks &
    Rotary Table
Leroi 50S2 Developmental Air Compressor
Screw Type Leveling Jacks
58' X 75,000 Lb. Derrick

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Tandem Axle Trailer

Get a Quote for this Vehicle
No Picture Available

Back to Top

1971 Gardner Denver 3000 Status: In Stock VIN#: 44

Rig Options
Single Drum Drawworks
17½"Rotary Table (not chain driven)
105 ft. 250,000 lb. Hydraulic Skytop Mast
Air clutch
Sub base 11' X 8' X 16' with Brewster Table and Right
    Angle Drive

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 2 Axle Tandem Trailer
Powered by a 6V-71 Detroit Diesel Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top
GP
GP-1100AR Brute Series Drill Status: In Stock VIN#: 0

Drill Options
12" Tube Style Mast
Two Way Cross Top Head Slide, Rack and Pinion
    Actuated
Planetary Top Head Drive
GP-1100 Hydrostatic Top Head Drive 0-160 rpm
11,000 Ft. Lbs Torque at 88 rpm
Dual Motor/Spindle Coring Attachment 750 rpm
    @ 1186 Ft. Lbs.
24' Stroke, Cable, Hydraulic Cylinder Actuated
    Pulldown/Retract Drill System
    (Pulldown 32,637#, Retract 32,637#)
Two Speed Retract
Dual Hydraulic Pump Drive System
HNW Inlet Coring Swivel 1 5/8" Hex
Hydrostatic Control
Oil Cooling System
Tachometer
Standard Lighting (2)
Tower Tool Carrier for Transportation
Hydraulic Slide Foot Guide with Hydraulic
    Tool Clamp
Outriggers, Tandem Truck Mount, Four Point
    Hydraulic Operated
Engine Friction Throttle
Operator Toot Stand, Helper Foot Stand
Terrell Power Tower Transfer Case with Air Clutch
Rotary Package: Mud/Air Hoses, Safety Cable,
    Valving, Piping, Suction Hose, Break-Out Wrench
Hydraulic Swing around Jib with Hydraulic
    Extension
12,000 # (First Layer) Pullmaster Winch with
    Rapid Reverse
1/2" X 200' Cable with Bearing Swivel
4,000 # First Layer GP Winch with Headache Ball
3/8" X 150' Cable with Swivel Hook
Rupe Auto Stroker with 1,000 LB. Winch
    and Cable
3X4X13 Magnum Centrifugal Mud Pump with
    Hydraulic Motor, HD Coupler, Frame
3L4 Moyno Progressive Cavity Mud Pump with
    Hydraulic Motor, Coupler, Frame
Injection Pump with Hydraulic Motor, Coupling
750 CFM/350 PSI Sullair Screw Air Compressor
    with Air Clutch, Transfer Case Drive, Frame,
    and Tank
Line Oiler Electric Actuated
Cushion Shock Sub
Stationary Drill Rod Rack, 20'
Slide for Drill Rod Rack
Tool Box
Drill Rod Adapter Attachment
Drill Rod Bushing
Dust Deflector
North Houston Wedge Lock Swivel
Hydraulic Slide Base
Plant Assembly and Installation

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on 1999 Navistar 2674, 220" WB
58,000 Lb. GVWR
18,000# Front Axle
40,000# Rear Axle
Cummins N14 435HP @ 2100 rpm
10 Speed with Overdrive
Air Brake System
425/65R 22.5 tires

Sale Price: $225,000

Get a Quote for this Vehicle

DES Sales Event Special
 
 
 
 
 
 
 
 

Back to Top
IDECO

IDECO Model HEB164377B Status: In Stock VIN#: 45

Rig Options

Torque Converter
Double Drum Drawworks with Air Clutches
Catheads
Hydraulically Raised and Telescoped Derrick
    (length & capacity?)
Racking Board
Ideco 275 Rotary Table
Three Sheave 125 Ton Block
125 Ton Swivel (make & model?)
Elevators
Make-Up & Breakout Tongs
Square Kelly & Roller Bushing

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Three Axle Trailer
P/B Rolls Royce Six Cylinder Diesel Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top
INGERSOLL-RAND

2001 Ingersoll-Rand T3W Status: In Stock VIN#: 0

Rig Options
  • Deck Engine - 5046 Hours
  • 1070/350 Air Compressor
  • 32' Mast
  • 32,500 Pullback
  • 20' Stroke
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 2001 International
  • 10 Speed Transmission
  • 3406 CAT C10 370 HP Engines (one drive, one deck)
  • 63 Gallon Diesel Drive Engine Tank
  • 22,592 Miles
Get a Quote for this Vehicle
Click Here for a Larger Picture
Click Here for a Larger Picture Click Here for a Larger Picture Click Here for a Larger Picture

Back to Top
2005 Atlas Copco T3W Status: In Stock VIN#: 0

Rig Options
Air Compressor: 1070/350
Derrick: 35 Foot
Water Pump: Cat 25gpm
Hydraulic Sand Line
46,000 Rears
20,000 Front Axle
3000 Hours

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
2005 Mack Granite
Automatic Transmission
400 H.P. Mack Engine
23,000 Miles

Sale Price: $425,000

Get a Quote for this Vehicle

DES Sales Event Special

Back to Top

1977 Ingersoll Rand T-4 Drill Status: In Stock VIN#: 0

Rig Options
900/350 IR Compressor
12V71 Deck Engine
    (1,800 Hours Since Overhaul)
Two Carrousels
6 Pod Main and 4 Pod Secondary
Two Wenches - 225’ of 4 ½”X 25’ Drill Rod
Two 6” Hammers, 7 ½” and 9” Bits
Three 4” Hammers, all 5 ½” Bits
11” Wing Bit with 5” Sub
10” Tri-Cone Bit (Mill Tooth) with 5” Sub
6” Tri-Cone Bit (Mill Tooth) with 4 ½” Sub
Break out tools

Customer responsible for all state and local taxes.

Truck Options
6V53T Carrier Engine

Get a Quote for this Vehicle
   

Back to Top

2005 Ingersoll-Rand T3W Status: In Stock VIN#: 46

Rig Options
900 cfm / 350 psi Compressor
3X4X13 Mission Magnum Centrifugal Mud Pump

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an International Chassis
P/B CAT Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1998 Ingersoll-Rand T3W Status: In Stock VIN#: 47

Rig Options
CAT 3406 Deck Engine
900 / 350 Compressor with Disconnect Clutch
18,000 lb. Main Winch
2,000 Lb. Sandreel
High Torque - Two Speed Tophead Drive
    - 8,000 Ft.-Lbs. Torque @ 0 - 107 RPM
    - 6,000 Ft.-Lbs. Torque @ 0 - 142 RPM
38' DHD Derrick with 29,500 Lbs. Pullback
Seven Rod Carousel Set-Up for 4-1/2" Drill Pipe
Bean 18 GPM Water Injection
DHD Lubricator

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Mack RD688S Chassis
P/B Mack E7 350 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1995 Ingersoll-Rand T3W Status: In Stock VIN#: 48

Rig Options
10,000 Total Hours
900 cfm / 350 psi Compressor
CAT 3406 Deck Engine
    (rebuilt 1000 hours ago)
All Hydraulic Pumps and Gear Box Were
    Replaced 2,500 Hours Ago
38' Derrick
Set-up For 4-1/2" Drill Pipe
500' of Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford 9000
With Air Operated Third Axle

Get a Quote for this Vehicle
No Picture Available

Back to Top

1995 Ingersoll-Rand T3W Status: In Stock VIN#: 49

Rig Options
3,400 Original Hours
900 cfm / 350 psi Compressor with
    Disconnect Clutch
32,500 Lbs. Pullback
18,000 Lbs. Single Line Main Winch
Seven Rod Carousel
Single Rod Loader
7 Gallon DHD Lubricator
Bean 18 GPM Pump
CAT 3406 Deck Engine
    (Price Includes the Installation of a Mission
     3X4X13 Centrifugal Mud Pump)

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford L9000 Chassis
11,000 miles
P/B CAT C12 350 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1993 Ingersoll-Rand T3W Status: In Stock VIN#: 50

Rig Options
Approximately 9,000 hours
900 cfm / 350 psi Compressor
CAT 3406 Deck Engine
38' DHD Derrick with 29,500 Lbs. Pullback
2,000 Lb. Sandreel
12,000 Lb. Single Line Main Winch
Set-Up for 4-1/2" Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Mack Chassis
Approximately 45,000 Miles

Get a Quote for this Vehicle
No Picture Available

Back to Top

1988 Ingersoll-Rand T3W Status: In Stock VIN#: 51

Rig Options
825 cfm / 350 psi Compressor
Cummings NTTA855 Deck Engine
Standard 32' Derrick with 26,500 Lbs. Pullback
12,000 Lb. Main Winch
CAT 12 GPM Water Injection Pump
Set-Up for 4-1/2" Drill Pipe
420' of Drill Pipe

1980 Kenworth Water Truck is Available for
     Additional Cost

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford 8000
300 HP Engine
New Tires

Get a Quote for this Vehicle
No Picture Available

Back to Top

1987 Ingersoll-Rand T3W Status: In Stock VIN#: 52

Rig Options
825 cfm / 350 psi Compressor
Cummins NTTA855 Deck Engine
    (rebuilt less than one year ago)
26,500 Lbs. Pullback
12,000 Lb. Single Line Main Winch
Bean 18 GPm Water Injection Pump
Dual Jib Boom Controls
DHD Lubricator
Seven Rod Carousel Set-Up for 4-1/2" Drill Pipe
Chassis is Painted Beige and the Drill is
    Painted Primer Grey.

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford 8000 Chassis
P/B Ford 7.8 Liter Engine
13 Speed Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

1991 Ingersoll-Rand TH75W Status: In Stock VIN#: 53

Rig Options
Cummins KT1919C 525 HP Deck Engine
HR2 900 cfm / 350 psi Compressor
55,000 Lbs. Pullback with Twin Inverted
    Feed Cylinders
Gearmatic 16,000 Lb. Single Line Main Winch
CAT 25 GPM Water Injection Pump
DHD Lubricator

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a HME VT100 Chassis
P/B Cummins 330 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

2003 Ingersoll-Rand T4W Status: In Stock VIN#: 54

Rig Options
5,000 Original Hours
Deephole Package (70,000 lbs. Pullback)
HR2.5 1250 cfm / 350 psi Air Compressor
High Torque Spur Gear Powerhead
    (8,000 Ft.-Lbs. @ 0 - 120 RPM)
CAT 25 GPM Water Injection Pump
DHD Lubricator
2,000' of Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a C.C.C.

Get a Quote for this Vehicle
No Picture Available

Back to Top

2003 Ingersoll-Rand T4W Status: In Stock VIN#: 55

Rig Options
Approximately 4000 Hours
HR2.5 1070 cfm / 350 psi Air Compressor
Cummins QSX15 Deck Engine
    (under 300 hours since bought new for $40,000)
Worm Gear Powerhead
Bean 18 GPM Water Injection Pump
7 Gallon DHD Lubricator
Two Auxiliary Four Rod Carousels

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top

2002 Ingersoll-Rand T4W Status: In Stock VIN#: 56

Rig Options
5,100 Hours
Ingersoll-Rand HR2.5 1070 cfm / 350 psi Air Compressor
Cummins QSX-15 600 HP Engine
    (rebuilt with "0" hours)
Worm Gear Tophead Drive with 6,000 Lb.-Ft. Torque
3,000' Capacity with 70,000 lbs. Pullback and
    Regeneration
Three Hydraulic Leveling Jacks
FMC Bean 20 GPM Water Injection Pump
DHD Electric Lubricator - 7 Gallon Capacity
Carousel and Auxiliary Drill Pipe Rack Set-Up to
    Hold 11 Pieces of 4-1/2" O.D. X 25' Long X
    2-7/8" IF
Basic Drill Pipe Handling Tools Included

This drill is in excellent condition and is ready to
    place into operation.

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Crane Carrier
P/B CAT C-10 335 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1991 Ingersoll-Rand T4W Status: In Stock VIN#: 57

Rig Options
Deephole Package
    (70,000 lbs. Pullback; Retrofitted by Atlas Copco
     in January 2007 for $50,000)
1050 cfm / 350 psi Compressor
New Denison Pumps Aug. of 2007
Rebuilt Cummins KTA19-C in March of 2008
    (Approximately 250 hours Since Completed)
Seven Rod Carousel
Four Rod Auxiliary Rod Holder
Worm Gear Powerhead
    (New Bearings in March 2008 and
    New Rotation Motor in October 2007)

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
CCC P/B Cummins L10 300 HP Engine
Fuller 8LL Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

1989 Ingersoll-Rand T4W Status: In Stock VIN#: 58

Rig Options
5,500 hours on total rebuild
900/350
Cummins KTA-19C 525 HP Engine
Worm Gear Power Head 6,000 Ft.-Lbs. Torque
DHD Lubricator
CAT 25 GPM Water Injection Pump
Carousel Set-Up to Hold Seven Pieces of
    4-1/2" O.D. X 25' Drill Pipe
Four Rod Auxiliary Side Rack

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on Crane Carrier
P/B Cummins L10 300 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1988 Ingersoll-Rand T4W Status: In Stock VIN#: 59

Rig Options
Cummins KTA19 Deck Engine
    (under 1,000 hrs. since rebuild)
HR2 900 cfm / 350 psi
    (under 1,000 hrs. since rebuild)
Worm Gear Powerhead
Myers 8 GPM Water Injection Pump
New Main Winch
300' of New Drill Pipe Included

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Hendrickson Carrier (29,000 Miles)
P/B Cummins L10 Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1988 Ingersoll-Rand T4W Status: In Stock VIN#: 60

Rig Options
HR2 900 cfm / 350 psi Air Compressor
Worm Gear Powerhead
36,500 lbs. Pullback
Bean 18 GPM Water Injection Pump
DHD Lubricator

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on CCC
Cummins KTA19 Deck Enigne
    (2,411 hours since rebuild)

Get a Quote for this Vehicle
No Picture Available

Back to Top

1987 Ingersoll-Rand T4W Status: In Stock VIN#: 61

Rig Options
900 cfm / 350 psi Compressor
Cummins KT19 Deck Engine

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Hendrickson Carrier

Get a Quote for this Vehicle
No Picture Available

Back to Top

1981 Ingersoll-Rand T4W Status: In Stock VIN#: 62

Rig Options
70,000 Lb. Deephole Package
Detroit 12V711TT 525 HP Engine
    (1,025 total run time on brand new engine)
900 cfm / 350 psi Compressor
Worm Gear Powerhead
Three Hole Hydraulic Pump Drive
Myers 8 GPM Water Injection Pump
7 Rod Carousel

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
CAT 3208 210 HP Crane Carrier Engine
13 Speed Road Ranger Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

1981 Ingersoll-Rand T4W Status: In Stock VIN#: 63

Rig Options
Deephole Package (70,000 lbs. pullback)
900 cfm / 350 psi Air Compressor
Detroit 12V92T Deck Engine
Worm Gear Powerhead
2000' of 4-1/2" O.D. X 25' Drill Pipe
Auxiliary 900 cfm / 350 psi Air Compressor
Fuel Truck
Drill Pipe Truck
Misc. Hammer & Bits

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top

1980 Ingersoll-Rand T4W Status: In Stock VIN#: 64

Rig Options
750 cfm / 150 psi Compressor
    (Unmounted but Owner will Reinstall for
     Price Listed)
Detroit 8V71 Deck Engine
Spur Gear Powerhead
No Carousel
500' of Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a CCC

Get a Quote for this Vehicle
No Picture Available

Back to Top

1975 Ingersoll-Rand T4BH Status: In Stock VIN#: 65

Rig Options
600 cfm / 250 psi Compressor
Detroit 8V71T Deck Engine
Venturi Style DHD Lubricator
Bean 12 GPM Water Injection Pump
Seven Rod Carousel
13' Stabilizer with 11" Tricone
250' of 4-1/2" X 25' Drill Pipe
6" Down-Hole-Drill
Petol Break-Out Wrench
Spare Front Tire
UL-88
Detroit 671 Starter
New Batteries
Main Pump Needs to be Rebuilt Because it Leaked
    all the Hydraulic Fluid from the System.

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
CCC P/B Detroit 671 Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1974 Ingersoll-Rand T4W Status: In Stock VIN#: 66

Rig Options
Detorit 8V71 Deck Engine
750 cfm / 150 psi Compressor
Worm Gear Powerhead

This Drill is for Parts and is Stated to be
    Mostly Complete

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
CCC
P/B Detroit 6V53 Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1973 Ingersoll-Rand T4W Status: In Stock VIN#: 67

Rig Options
Detroit 12V71TT Deck Engine
Ingersoll-Rand 900 cfm / 350 psi Compressor
    (rebuilt)
All Hydraulic Pumps and Hydraulic Motors Have
    Been Rebuilt
Capable of Setting 38' Casing

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an 8X4 Crane Carrier
P/B CAT 3406 Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1970 Ingersoll-Rand T4BH Status: In Stock VIN#: 68

Rig Options
600 cfm / 150 psi Compressor
Detroit 8V71 Deck Engine
Worm Gear Power Head
Seven Rod Carousel Plus
Drill Has Been Sitting Idle for Eight Years

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
CCC
P/B International 501 Gasoline Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1985 Ingersoll-Rand TH60 Status: In Stock VIN#: 69

Rig Options
750 cfm / 250 psi Compressor
Gardner Denver 5" X 6" Mud Pump
38' Derrick with 29,500 Lbs. Pullback
Bean 18 GPM
DHD Lubricator
Set-Up to Handle 4-1/2" X 20' Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1986 GMC General Chassis
P/B Detroit 8V92TA Engine
    (rebuilt one year ago)

Get a Quote for this Vehicle
No Picture Available

Back to Top

1982 Ingersoll-Rand TH60 Status: In Stock VIN#: 70

Rig Options
750 cfm / 250 psi Compressor
38' Long Derrick with 30,000 Lbs. Pullback
Spur Gear Four Motor Tophead Drive
Gearmatic 16,000 Lb. Capacity Main Winch
2,000 Lb. Capacity Sandreel
Seven Rod Carousel Set-Up for 4-1/2" Drill Pipe
Myers 8 GPM Water Injection Pump
Venturi Style DHD Lubricator
Four Hydraulic Leveling Jacks
New Style Side-by-Side Cooler Assembly
    (Similar to T3W's)

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an International Paystar 5000 Chassis
P/B Detroit 8V92TA 475 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1979 Ingersoll-Rand TH60 Status: In Stock VIN#: 71

Rig Options
750 cfm / 250 psi Compressor
Gardner Denver 5" X 6" Hydraulically Driven
    Mud Pump
38' Long Derrick with 30,000 Lbs. Pullback
Aardvark Casing Hammer
Spur Gear Four Motor Tophead Drive
Gearmatic 16,000 Lb. Capacity Main Winch
2,000 Lb. Capacity Sandreel
2,000 Lb. Capacity Utility Hoist
Seven Rod Carousel Set-Up for 4-1/2" Drill Pipe
Myers 8 GPM Water Injection Pump
Venturi Style DHD Lubricator
Seven Gallon Electric DHD Lubricator
Four Hydraulic Leveling Jacks

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an International Paystar 5000 Chassis
P/B Detroit 8V92TA 475 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Ingersoll-Rand TH60 Status: In Stock VIN#: 72

Rig Options
600 cfm / 250 psi Compressor
38' Long Derrick with 30,000 Lbs. Pullback
Spur Gear Four Motor Tophead Drive
Gearmatic 16,000 Lb. Capacity Main Winch
2,000 Lb. Capacity Sandreel
Seven Rod Carousel Set-Up for 4-1/2" Drill Pipe
Myers 8 GPM Water Injection Pump
Venturi Style DHD Lubricator
Three Hydraulic Leveling Jacks
New Style Side-by-Side Cooler Assembly
    (Similar to T3W's)

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an International Paystar
    5000 Chassis
P/B Detroit 8V71T 318 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1978 Ingersoll-Rand TH60 Status: In Stock VIN#: 73

Rig Options
750 cfm / 250 psi Compressor
Gardner Denver 5" X 6" Pump
Rebuilt the Following Items Prior to Parking Six
    Years Ago:
    - Powerhead
    - Gardner Denver Pump
    - Air Compressor
    - Cotta PTO
    - Hydraulic Pumps

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an International Paystar
    5000 Chassis
P/B Detroit 8V92TA 475 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1974 Ingersoll-Rand TH60 Status: In Stock VIN#: 74

Rig Options
LeRoi (500 cfm / 250 psi) Air Compressor

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top
JOY SULLIVAN

Joy Sullivan 300 Status: In Stock VIN#: 76

Rig Options
(4,000' Capacity)
Single Drum Drawworks
P/B NEW Scania 6 Cylinder Diesel Engine
7/8" Drilling Line
Rebuilt 750 Allison Transmission
85' Hydraulically Raised Single Piece Derrick
    (new in 1983)
15" Shaft Driven Rotary Table
Rebuilt Guard Rails
New Tires
Shorty Block & Hook
Swivel
Kelly
Specially Designed Right Angle Drive Gearbox

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Three Axle Trailer

Get a Quote for this Vehicle
No Picture Available

Back to Top
MAYHEW

Mayhew 1000 Status: In Stock VIN#: 77

Rig Options
Gardner Denver 4X5 Mud Pump
5-1/4" Stationary Table
Portable Mud Pit
400' of 2-3/8" X 15' X Mayhew Junior Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 2000 Chevy Kodiak Single
    Axle Chassis
P/B Gasoline Engine
15,000 Miles

Get a Quote for this Vehicle
No Picture Available

Back to Top

Misc. Mayhew 1000's Status: In Stock VIN#: 78

Rig Options
Misc. Mayhew 1000's for Sale

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top

Mayhew 1000 Status: In Stock VIN#: 79

Rig Options
Hydraulically Driven Wheatley 6X6 Mud Pump
Hydraulically Driven 7-1/2" Stationary Rotary
    Table
Mechanical Clutches on the Drawworks
Drill Pipe Rack
Two Rear Hydraulic Jacks
Hydraulic Chain Pulldown

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1986 GMC Brigadier
P/B Detroit Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

Mayhew 1000 Status: In Stock VIN#: 80

Rig Options
Gardner Denver 5" X 6" Mud Pump
No Air Compressor
Rig was built for a customer with new components
    and never used since built approx. 7 years ago

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Mid 1980's 6X4 International
    Chassis
P/B IHC DT466 210 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

Two Mayhew 1000's Status: In Stock VIN#: 81

Rig Options
Gardner Denver 5" X 6" Mud Pump
Set-Up to Handle 20' Drill Pipe
Both Rigs Are in Fair to Poor Condition,
    but They Both Run and Operate

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top

Mayhew 1000 Status: In Stock VIN#: 82

Rig Options
Leroi 100S1 Compressor (700 cfm / 50 psi)
Gardner Denver 5" X 6" Mud Pump
7-1/2" Stationary Rotary Table
Manual Clutches on the Drawworks
Two Hydraulic Leveling Jacks
Hydraulic Chain Pulldown
23' Fluted Kelly
Rig has been sitting for six years

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1981 Ford 4X2 Chassis
P/B 429 Gasoline Engine
    (needs work on carburetor)

Get a Quote for this Vehicle
No Picture Available

Back to Top

Mayhew 1000 Status: In Stock VIN#: 83

Rig Options
No Chassis
No Mud Pump
No Air Compressor

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options

Get a Quote for this Vehicle
No Picture Available

Back to Top

Late 1950's Mayhew 1000 Status: In Stock VIN#: 84

Rig Options
Wheatley 6X6 Pump
No Air Compressor
Stationary 5-1/4" Rotary Table
No Leveling Jacks
Gardner Denver Tear Drop Single Sheave Block
Sandline Drum
Chain Pulldown
Mechanical Friction Clutches on the Drawworks
Set-Up to Handle 15' Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1950's International 4X2 Chassis
P/B Gasoline Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

Late 1950's Mayhew 1000 Status: In Stock VIN#: 85

Rig Options
5" X 6" Gardner Denver Mud Pump
    (rebuilt recently)
340' of 2-3/8" O.D. Drill Pipe
Three 20' Drill Collars
Tools
Two Hydraulic Jacks on Front
Mechanical Pulldown
5-1/4" Stationary Rotary Table

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1969 International 6X4
     Chassis
P/B Propane Engine
    (engine needs work)

Get a Quote for this Vehicle
No Picture Available

Back to Top

1950's Mayhew 1000 Status: In Stock VIN#: 86

Rig Options
Gardner Denver 427 Compressor
200' (15' lengths) of 2-3/8" O.D. Drill Pipe
5-1/4" Non-Retractable Rotary Table
Mechanical Clutches

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Single Axle 1962 Ford 600
    Chassis
P/B 534 Gasoline Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top
MIDWAY

Midway 1300 Status: In Stock VIN#: 87

Rig Options
Gardner Denver 5-1/2" X 8" Mud Pump
Leroi Reciprocating Air Compressor
Gardner Denver 1400 Air Clutch Drawworks
Hydraulic Chain Pulldown
Hydraulic Leveling Jacks
Drill Pipe Rack

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1979 International Chassis

Get a Quote for this Vehicle
No Picture Available

Back to Top

Midway 1300 Status: In Stock VIN#: 88

Rig Options
Gaso 1550C 5X10 Pump
No Air Compressor
No Bailing Drum
7-1/2" Stationary Rotary Table
Two Rear Hydraulic Leveling Jacks
Mechanical Friction Clutches on the Drawworks
Square Tubing Mast
Chain Pulldown (Missing Chains Only)
20' Drill Pipe Rack
No Drill Pipe

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1980's International 6X4 Chassis
P/B Detroit 671 Engine
13 Speed Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

Midway 1300 Status: In Stock VIN#: 89

Rig Options
3TA92 Transfer Case
LeRoi 256S2 Compressor
Gardner Denver 5X6 Mud Pump
Midway 8-1/2" Stationary Rotary Table
Mechanical Friction Clutches
Four Hydraulic Leveling Jacks
New Tires on Chassis (missing two)

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1988 Freightliner Chassis
P/B Cummins 350 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

Midway 13M Status: In Stock VIN#: 90

Rig Options
6" Wide Brake Bands on the Drawworks
Square Tubing Derrick
Gardner Denver 7-1/2" Retractable Rotary Table
Gardner Denver 5X8 Mud Pump
Gardner Denver WCQ (427 cfm / 50 psi)
    Air Compressor
Bailing Brum
Four Hydraulic Leveling Jacks
Mechanical Friction Clutches on the Drawworks
3-1/2" O.D. X 24' Fluted Kelly

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 2007 Mack Chassis
P/B 405 HP Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

Midway 15M Status: In Stock VIN#: 91

Rig Options
8" X 22"Brake Bands on Drawworks
35' Long Derrick Rated for 75,000 Lbs. Capacity
    with 3" Square Tubing
Midway 8-1/2" Retractable Rotary Table
Gardner Denver 5-1/2" X 8" Mud Pump
Ingersoll-Rand P185 Compressor with Independent Diesel Engine Mounted On Deck
Bailing Brum
Four Hydraulic Leveling Jacks
Air Clutches on the Drawworks
3-1/2" O.D. X 24' Fluted Kelly

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 2006 Mack Chassis

Get a Quote for this Vehicle
No Picture Available

Back to Top

1980 Midway 15M Status: In Stock VIN#: 92

Rig Options
Gardner Denver 5-1/2" X 8" Mud Pump
LeRoi 750 cfm / 350 psi Screw Compressor
Air Clutches on the Drawworks
Sandline Drum
FMC Bean 9 GPM Water Injections Pump
Hydraulic Cathead
5-1/4" O.D. X 24' Long Fluted Kelly
Two Sheave Traveling Blocks
Midway 8-1/2" Retractable Rotary Table
+50' Derrick Rated for 75,000 lbs. with 3"
    Square Tubing
Drill Pipe Racking Board
No Drill Pipe Rack
Four Hydraulic Leveling Jacks

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1980 Paystar 5000 Chassis
P/B Rebuilt Detroit 8V92TA 435 HP Engine
    ("0" Hours on Rebuild)

Get a Quote for this Vehicle
No Picture Available

Back to Top

1980 Midway 15M Status: In Stock VIN#: 93

Rig Options
8-1/2" Retractable Table
52' 3" Square Tubing Derrick Rated for 60,000 Lbs.
Set-Up on Four Lines
Air Clutches
Sandline with 1,000' Cable
Drill Pipe Rack
Gardner Denver 5-1/2" X 8" Mud Pump
Ingersoll-Rand 586 cfm / 125 psi Compressor
70,000 lb. Pad Type Weight Indicator
Two Pin Geolograph
2,300' of 3-1/2" O.D. 30' - 31' Drill Pipe
(17) 5-1/2" Drill Collars 27' - 29' Long
(1) 8-5/8" Rotating Head
(1) 12-1/2" Flange Type Rotating Head
Bowl for Rotating Head to fit 2-3/8" - 8-5/8" Pipe
Slips and Elevators
Hydrill Type BOP

1980 GMC General Water Truck with 3,000 Gallon
    Tank on 30' Float
Detroit 8V71 Engine
Drill Pipe Storage on Both Sides

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford 9000 Chassis
P/B Detroit 8V71 Engine
13 Speed Road Ranger Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

Midway 1500 (shop built) Status: In Stock VIN#: 94

Rig Options
Gardner Denver 5-1/2" X 8" Mud Pump
Heavy Tubing Long Derrick
7-1/2 Non-Retractable Table
Pulldown Has Been Removed
Four Hydraulic Jacks

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1981 International 6X4 Chassis

Get a Quote for this Vehicle
No Picture Available

Back to Top

1977 Midway 1500MW Status: In Stock VIN#: 95

Rig Options
Gardner Denver 5" X 8" Mud Pump
LeRoi 100S1 Air Compressor
Retractable 8-1/2" Rotary Table
Air Clutches on the Drawworks
Drill Pipe Rack
35' Derrick with 2-1/2" Square Tubing
Four Hydraulic Leveling Jacks
4-1/2" O.D. X 24' Long Kelly
300' of 4-1/2" O.D. X 2-7/8" IF Flush Joint Drill Pipe
Sandline Drum
Rig is Very Clean and Runs Very Quite

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Ford 9000 Chassis
P/B Cummins 290 HP Engine
9 Speed Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top

Midway 1000 Status: In Stock VIN#: 96

Rig Options
3X4 Centrifugal Mud Pump
Two Cylinder Developmental Air Compressor
5-1/4 Non-Retractable Rotary Table
Square Tubing Derrick

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on an International 549 Chassis
P/B Propane Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top
MISCELLANEOUS

2001 Econoline Trailer Status: In Stock VIN#: 0

Rig Options
  • 29 Foot
  • 15 Ton Tilt
  • Refloored
  • New Tires
  • New Axle
  • Approximately 4000 Miles
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Sale Price: $13,500

Get a Quote for this Vehicle

DES Sales Event Special
Click Here for a Larger Picture
Click Here for a Larger PictureClick Here for a Larger Picture

Back to Top

1989 Peterbilt 375 Status: In Stock VIN#: 0

Rig Options
  • CAT Engine
  • 9 Speed
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Sale Price: $15,000

Get a Quote for this Vehicle

DES Sales Event Special
Click Here for a Larger Picture
Click Here for a Larger PictureClick Here for a Larger Picture

Back to Top

2007 Yanmar VIO 75 Trackloader Status: In Stock VIN#: 0

Rig Options
  • 450 Hours
  • Hydraulic Thumb
  • Heat & A/C Cab
  • Extra Hydraulic Circuit for Hydraulic Hammer
  • LIKE NEW!!
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Sale Price: $55,000

Get a Quote for this Vehicle

DES Sales Event Special
Click Here for a Larger Picture
Click Here for a Larger PictureClick Here for a Larger PictureClick Here for a Larger Picture

Back to Top

PULSTAR 8000E Status: In Stock VIN#: 0

Rig Options
  • Pulstar 8000E with Hydraulic Outriggers and Holding Valves
  • 4,000 lb Single Line Pull
  • 36 ft Tower Height
  • Solid Aluminum Pipe Racks (2) with Rack Straps
  • 1650 ft lbs of Torque
  • 5,600 lbs Pullback, 10,000 lbs Pulldown
  • Air Compressor 90 CFM/175 PSI
  • Centerline 7 1/2 x 10 Piston Mud Pump 190 GPM/225 PSI
  • 200' of Aluminum Heavy Wall Drill Rod - Weighs 33 lbs each
Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 2006 Ford F550
  • 4x4
  • 165" Wheelbase
  • 6.0L Power Stroke Diesel
  • 6 Speed
  • Locking Differential
  • Heavy Duty Rear Suspension
Get a Quote for this Vehicle
   
Click Here for a Larger Picture
Click Here for a Larger PictureClick Here for a Larger PictureClick Here for a Larger Picture

Back to Top

2002 214S Tool Carrier JCB Loader Backhoe Status: In Stock VIN#: 0

Rig Options
  • 4 in 1 Bucket
  • Heat & A/C Cab
  • Radio
  • Extend-A-Hoe with 24" Bucket
  • Loaded
  • 220 Hours
  • Also Available:
    • Brush Grapple
    • Forklift Attachment
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES



Sale Price: $50,000

Get a Quote for this Vehicle

DES Sales Event Special

Back to Top

Mud Pump Status: In Stock VIN#: 0

Pump Options

7.5 piston

10” stroke
Gardner Denver
Model # FO FXO E
Serial # 110011
671 Detroit
65 RPM/355 PSI
Shaft oiler

Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Trailer

Get a Quote for this Vehicle

Back to Top
MOBILE

1997 Mobile Equipment SR35 Status: In Stock VIN#: 97

Rig Options
4,500 Hours
CAT 3412 Deck Engine
Sullair 1350 / 350 Compressor
110,000 Lbs. Pullback
34' Stroke Tophead Drive
Braden 25,000 Lb. Casing Hoist Set-Up on
    Four Part Line with 42' Clearance
No Carousel
27" Table Opening
3" Air Piping

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on Hendrickson Five Axle Carrier
P/B CAT 3408 450 HP Engine
Six Speed Automatic Transmission

Get a Quote for this Vehicle
No Picture Available

Back to Top
PORTADRILL

1979 Portadrill TKS Status: In Stock VIN#: 98

Rig Options
43' Derrick
Sullair 750 cfm / 250 psi Compressor
Mission Magnum 3X4 Centrifugal Pump
4-1/2" X 24' Kelly
Drill Pipe Rack
Detroit 8V92NA Deck Engine
Three Hydraulic Leveling Jacks
Hydrostatically Powered 7-1/2" Retractable
    Rotary Table
Hydrostatically Powered Drawworks
Hydraulic Chain Pulldown

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a Paystar 5000 6x6
P/B International DT466 Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1974 Portadrill 10TE Status: In Stock VIN#: 99

Rig Options
Atlas Copco DT4 Compressor
No Mud Pump
Tophead Drive

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 6X4 Crane Carrier
P/B Gasoline Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top

1973 Portadrill 521 Status: In Stock VIN#: 100

Rig Options
Rig is PTO Driven
Gardner Denver 5" X 6" Pump

Customer responsible for all state and local taxes.
Equipment as is, where is - NO WARRANTIES

Truck Options
Mounted on a 1973 GMC
P/B 454 Gas Engine

Get a Quote for this Vehicle
No Picture Available

Back to Top
PUMP HOISTS

Pulstar P7000 Status: In Stock VIN#: 0

Rig Options
  • Hydraulic Outriggers and Holding Valves
  • Remote Control
  • 37 ft Tower Height
  • Pipe Rack with Rack Straps
  • Sandline
  • Heavy Duty Tailgate
  • Throttle Commander
  • Walking Beam
  • Water Tank
  • 9' Flatbed with Underdeck Toolboxes
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 1996 Ford F350
  • 4x4
  • Color: White
  • 460 Gas Eengine
  • Approximately 45,000 Miles
Get a Quote for this Vehicle
Click Here for a Larger Picture
Click Here for a Larger Picture Click Here for a Larger Picture Click Here for a Larger Picture

Back to Top

Pulstar P12000 Status: In Stock VIN#: 0

Rig Options
  • P12000 with Hydraulic Outriggers and Holding Valves
  • Hoist Painted Gray
  • Remote Control
  • 37 ft Tower Height
  • (2)Solid Aluminum Pipe Rack with Rack Straps
  • Sandline with Freefall (Less Cable and Hook)
  • Heavy Duty Tailgate
  • Factory Mount with Hydraulic Oil
  • Throttle Commander
  • Omaha Standard 108D54VT Lift Top Service Body
  • Heavy Duty Tow Bumper & Hitch
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 2004 Ford F550 4x4
  • Color: Red
  • Air Conditioning
  • 6.0L Power Stroke Diesel
  • 6 Speed
  • Locking Differential
Get a Quote for this Vehicle
Click Here for a Larger Picture
Click Here for a Larger Picture
Click Here for a Larger Picture Click Here for a Larger Picture

Back to Top

Pulstar P38000 Status: In Stock VIN#: 0

Rig Options
  • (2) Rear Hydraulic Outriggers and Holding Valves
  • Rapid Hoist Feature
  • 48 ft Tower Height
  • Hydraulic Power to Rear
  • Hydraulic Oil Cooler
  • Dual Front Outriggers with Failsafe Lock Valves
  • Hydraulic Reservoir Heater
  • Mast Light Kit with Guards
  • Power Tongs Hydraulic Source with Special Pressure Relief and Gauges
  • Power Tongs Handler Jib Boom
  • Air Plumbed to Rear
  • Hydraulic Outlets Plumbed to Rear
  • 8' x 14' 6" all Steel Heavy Duty Flatbed and Headache Rack
  • ICC Clearance Lights, Reflectors
  • SS Rear Recessed Lights
  • (2) 48" Underdeck Steel Toolboxes
  • Recessed/Sunken Crossmembers in Center of Flatbed to Allow Recessed Mounting of Rig Frame Below Floor Level
  • Rear Light Skirt with Heavy Duty Tow Bumper
  • Mud Flaps and Brackets
  • Special Heavy Duty Bumper to Hold Power Tongs with Removable Gate
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 2005 Sterling Acterra
  • Color: White
  • Diesel
  • 10 Speed
  • 12,000# Front Axle
  • 21,000# Rear Axle
  • Single Rear Axle
Get a Quote for this Vehicle
Click Here for a Larger Picture
Click Here for a Larger Picture
Click Here for a Larger Picture
Click Here for a Larger Picture

Back to Top

Pulstar P7000 Status: In Stock VIN#: 0

Rig Options
  • Hydraulic Outriggers and Holding Valves
  • Remote Control
  • 40 ft Tower Height
  • (1) Solid Aluminum Pipe Rack with Rack Straps
  • Front Jack, XL
  • Mast Mounted Lights with Guards
  • Heavy Duty Tailgate
  • Factory Mount with Hydraulic Oil
  • Throttle Commander
  • Omaha standard 108D54VT Lift Top Service Body
  • Aluminum Fronts, Tops, Rears
  • Stainless Steel Paddle Latches
  • Deluxe Through Compartment
  • Wire Mounts, Front and Rear
  • Heavy Duty Tow Bumper & Hitch
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 2004 Ford F550 4x4
  • 144" Wheel Base
  • Air Conditioning
  • 6.0L Power Stroke Diesel
  • 6 Speed
  • Locking Differential
  • Chrome Bumper
  • AM/FM CD
  • Tilt
  • Cruise
  • Heavy Duty Rear Suspension
  • Power Windows & Locks
  • Stainless Steel Wheel Simulators
Get a Quote for this Vehicle
Click Here for a Larger Picture
Click Here for a Larger Picture
Click Here for a Larger Picture

Back to Top

Swinger 360 Status: In Stock VIN#: 0

Rig Options
  • ½" X 150' Non-Rotating Cable with Safety Hook - Fail Safe Brakes
  • 2 speed
  • Remote Control
  • PTO & Pump
  • Four Hydraulic Jacks - 3½" X 2" X 30"
  • Hydraulic Oil
  • Hydraulic Boom Push Out
  • Rotation Bearing Mounted in Bed & Operated Hydraulicly Through Rotation Gear Box
  • Rotation of Boom is 240 Degrees and Layback 10'
  • 14' Flat Bed
Customer responsible for all state and local taxes
Equipment as is, where is - NO WARRANTIES

Truck Options
  • 1997 Ford F800
Sale Price: $40,000

Get a Quote for this Vehicle

DES Sales Event Special